Mercury-marine Ocean Runner 898393001 Manuel d'utilisateur

iAll of us at Mercury Marine want to thank you for choosing aMercury Marine Inflatable boat. You have made a soundinvestment in boating pleasu

GENERAL INFORMATION6Boater's ResponsibilitiesThe operator (driver) is responsible for the correct and safeoperation of the boat and

GENERAL INFORMATION7Lanyard Stop SwitchThe purpose of a lanyard stop switch is to turn off the engine whenthe operator moves far enough away from the

GENERAL INFORMATION8Important Safety Information: The purpose of a lanyard stop switchis to stop the engine when the operator moves far enough awayfro

GENERAL INFORMATION9! WARNINGAvoid serious injury or death from deceleration forces resultingfrom accidental or unintended stop switch activation. The

GENERAL INFORMATION10WHILE BOAT IS STATIONARY! WARNINGStop your engine immediately whenever anyone in the water isnear your boat. Serious injury to th

GENERAL INFORMATION11There is another less common hazardous result from allowing yourboat to launch off a wave or wake. If the bow of your boat pitche

GENERAL INFORMATION12• The boat could move suddenly in a new direction. Such asharp change in direction can cause occupants to be thrownout

GENERAL INFORMATION13! WARNINGAvoid the combination of a running engine and poor ventilation.Prolonged exposure to carbon monoxide in sufficient

GENERAL INFORMATION14WHILE BOAT IS MOVINGab21628a - Running the boat with the trim angle of the bow too highb - Running the boat with no forward hatch

GENERAL INFORMATION15Never be under the influence of alcohol or drugs while boating (itis the law). Alcohol or drug use impairs your judgment and grea

iiRecord your Hull Identification Number (HIN) and engine model/serial number. The HIN is located on the back of the boat on thestarboard side. The en

GENERAL INFORMATION16SpecificationsDescriptionModel300 330 350Dry weight 59 kg (130 lb.) 69 kg (152 lb.) 84 kg (185 lb.)Maximum load 475 kg (1047 lb.)

GENERAL INFORMATION17Manufacturer's PlateThe manufacturer's plate is located on the inside of the boattransom.abcdefghi14598a - Bo

GENERAL INFORMATION18Boat Design Categories Navigation Wind Force and Wave HeightC InshoreDesigned for voyages in coastalwaters, large bays, estuaries

BOAT COMPONENTS19Components Location ‑ Model 300BACK VIEWa24439a - Hull identification number (HIN)FRONT VIEWa24441a - Front mooring ring

BOAT COMPONENTS20TRANSOM VIEWabcdec24447a - Drain plugb - Hull drain plugc - Rear lifting ringd - Motor platee - Manufacturer's plate

BOAT COMPONENTS21SIDE VIEWbcdea24448a - Port air chamber valveb - Front air chamber valvec - Front lifting ringd - Starboard air chambervalvee - OarsC

BOAT COMPONENTS22FRONT VIEWa24441a - Front mooring ringTRANSOM VIEWabcdb24451a - Drain plugb - Rear lifting ringc - Motor plated - Manufacturer's

BOAT COMPONENTS23SIDE VIEWabef24452cda - Paddle locationb - Port air chamber valvec - Front lifting rings (2)d - Front air chamber valvee - Storage co

TRANSPORTING24Trailering BoatUse a trailer that will properly support the boat hull. Position theboat on the trailer so it will rest in a stable posit

OPERATION25Inflation! CAUTIONDo not use a compressed air source to fill air chambers. Overinflation may result in damaged seams and or bulkheads. Seam

TABLE OF CONTENTSiiiWARRANTY INFORMATIONTransfer of Warranty...1Warranty Registration

OPERATION26NOTE: Always be aware of the air pressure in the air chambers.The air volume inside the air chambers will expand as the internalair tempera

OPERATION27Empty the boat of all equipment. Make sure nobody is on‑boardduring lifting.14774Outboard PowerChoose an outboard for the boat that is i

OPERATION28• Check the outboard for tightness on the transom.• Know the fuel capacity and cruising range.• Check that the lanyard stop switch fo

OPERATION29Drain Valve OperationWhen underway, remove the drain plug from the drain and thewater will automatically run out. The inner diaph

OPERATION30TowingIf the inflatable boat is to be towed by another boat, the inflatableboat must be empty. Remove outboard, fuel tank and equipment.Att

MAINTENANCE31Cleaning ProcedureFABRIC SURFACESInflate the air chambers. Clean the fabric with a mild soap and freshwater solution. Rinse with fresh wa

MAINTENANCE32The repair kit which comes with the boat is a one part glueoperation and should be used for emergency minor repair. For aperm

MAINTENANCE33Apply two thin layers of adhesive using a short bristle brush, in acircular pattern on both the backside of the patch and the patcharea

MAINTENANCE34For the best results when gluing, the relative humidity should beless than 60%, ambient air temperature should be between18 °C to

STORAGE35Storage PreparationNOTE: The boat should be cleaned and rinsed with fresh waterbefore being placed in long term storage. Refer to cl

TABLE OF CONTENTSivDrain Valve Operation...29Loading...

OWNERS SERVICE ASSISTANCE36Service AssistanceYour satisfaction with your inflatable product is very important toyour dealer and to us. If you ev

WARRANTY INFORMATION1Transfer of WarrantyThe limited warranty is transferable to a subsequent purchaser, butonly for the remainder of the unused porti

WARRANTY INFORMATION2Mercury MarineAttn: Warranty Registration DepartmentW6250 W. Pioneer RoadP.O. Box 1939Fond du Lac, WI 54936-1939920-929-5054Fax 9

WARRANTY INFORMATION3DURATION OF COVERAGEThe fiberglass hull, air deck® floor, all hull attachments andaccessories, but not limited to, floor

WARRANTY INFORMATION4HOW TO OBTAIN WARRANTY COVERAGEThe customer must provide Mercury with a reasonable opportunityto repair, and reasonable acces

WARRANTY INFORMATION5DISCLAIMERS AND LIMITATIONS:THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE ARE EXPRESSLY DISCLAIME